HO2000 preliminary 1000.0 mhz saw oscillator rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-8148 e-mail: info@rfm.com page 1 of 2 rfm europe sales phone: (33-0) (1) 39.16.42.89 fax: (33-0) (1) 39.16.42.70 http://www.rfm.com ?1998 by rf monolithics, inc. the stylized rfm logo and rfm are registered trademarks of rf monolithics, inc. HO2000-a-022599 ? saw frequency stabilization ? fundamental-mode oscillation at 1000.0 mhz ? a rugged, compact general-purpose oscillator the frequency of this oscillator is stabilized by saw technology. this results in ex- cellent performance form a compact, rugged, oscillator operating at the fundamental frequency of 1000.0mhz. the HO2000 is suitable for general purpose use in a wide variety of applications. absolute maximum ratings electrical characteristics rating value units dc supply voltage 0 to +6 vdc ambient temperature powered -40 to +70 c storage -40 to +85 characteristic sym notes minimum typical maximum units operating frequency absolute frequency f o 1, 7 999.800 1000.200 mhz tolerance from 1000.0 mhz d f o 200 khz rf output power p o 3, 6 +7 +10 dbm discrete spurious outputs second harmonics 2, 3, 4 -15 dbc third and higher harmonics -20 nonharmonic <-100 -80 ssb phase noise 1 khz offset 2, 3, 4 -95 dbc/hz 10 khz offset -130 -125 rf impedance nominal impedance z o 3 50 w operating load vswr g l 3, 5 -40 2:1 dc power supply operating voltage v cc 3, 6 +4.75 +5 +5.25 vdc operating current i cc 30 50 ma operating ambient temperature t a 3, 6 -20 +70 c lid symbolization (yy = year, ww = week) rfm HO2000 yyww dip 14-8 case block diagram electrical connections rf output v cc buffer amplifier saw oscillator (8 pins in a 14-pin configuration) top view 1 v v cc cc case ground 2 case ground 6 rf output 7 13 case ground 9 case ground 8 cc caution: electrostatic sensitive device. observe precautions for handling cocom caution: approval by the u.s. department of commerce is required prior to export of this device. notes: 1. one or more of the following united states patents apply: 4,616,197; 4,610,681; and 4,761,616. 2. unless noted otherwise, all specifications are listed at t a = +25c 2c, v cc = nominal voltage 0.01 vdc, and load impedance = 50 w with vswr 1.5:1. 3. the design, manufacturing process, and specifications of this device are subject to change without notice. 4. applies to oscillator only and not to sidebands caused by external electrical or mechanical sources. (dedicated external voltage regulation with low-frequency filtering for the dc power supply and proper circuit board layout are recommended for optimum spectral purity.) 5. for specified maximum operating load vswr (any angle) at f o . (no instability or damage will occur for any passive load impedance.) 6. for any combination of v cc and t a within the specified operating ranges. 7. applies for any combination of note 5 and 6 conditions.
HO2000 preliminary 1000.0 mhz saw oscillator rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-8148 e-mail: info@rfm.com page 2 of 2 rfm europe sales phone: (33-0) (1) 39.16.42.89 fax: (33-0) (1) 39.16.42.70 http://www.rfm.com ?1998 by rf monolithics, inc. the stylized rfm logo and rfm are registered trademarks of rf monolithics, inc. HO2000-a-022599 dip14-8 metal dual-inline package with 8 leads in a 14-lead dip configuration dimension mm inches min max min max a ? 20.45 ? 0.805 b ? 12.83 ? 0.505 c ? 6.35 ? 0.250 d 0.40 0.51 0.016 0.020 e 0.64 nominal 0.025 nominal f 7.62 nominal 0.300 nominal g 2.54 nominal 0.100 nominal h 15.24 nominal 0.600 nominal k 5.97 6.73 0.235 0.265 l 1.30 ? 0.051 ? m ? 11.18 ? 0.440 n ? 18.80 ? 0.740 r 1.75 2.26 0.069 0.089 top view bottom view d (8 places) b m a n e pin 1 mark (optional) (4 places) l c k f r (3 places) h g (4 places) 1 2 6 7 8 9 13 14
|
